Nonan-1-ol is an organic/chemical reagent widely used in the manufacture of surfactants, lubricants, etc. It could be utilized as a detergent, emulsifier and stabilizer, and is extensively used in certain cosmetics, personal care products and printing inks. In addition, the compound has important applications in certain industrial sectors, such as in plastics and rubber production processes.

Physicochemical Properties

Molecular Formula	C9H20O
Molecular Weight	144.26
Exact Mass	144.151
CAS #	143-08-8
Related CAS #	Nonan-1-ol-d19;349553-86-2;Nonan-1-ol-d4;33975-46-1
PubChem CID	8914
Appearance	Colorless to yellowish liquid
Density	0.827 g/mL at 25 °C(lit.)
Boiling Point	215 °C(lit.)
Melting Point	−8-−6 °C(lit.)
Flash Point	208 °F
Vapour Pressure	13 mm Hg ( 104 °C)
Index of Refraction	n20/D 1.433(lit.)
LogP	2.729
Hydrogen Bond Donor Count	1
Hydrogen Bond Acceptor Count	1
Rotatable Bond Count	7
Heavy Atom Count	10
Complexity	52.7
Defined Atom Stereocenter Count	0
SMILES	O([H])C([H])([H])C([H])([H])C([H])([H])C([H])([H])C([H])([H])C([H])([H])C([H])([H])C([H])([H])C([H])([H])[H]
InChi Key	ZWRUINPWMLAQRD-UHFFFAOYSA-N
InChi Code	InChI=1S/C9H20O/c1-2-3-4-5-6-7-8-9-10/h10H,2-9H2,1H3
Chemical Name	nonan-1-ol
HS Tariff Code	2934.99.9001
Storage	Powder-20°C 3 years 4°C 2 years In solvent -80°C 6 months -20°C 1 month
Shipping Condition	Room temperature (This product is stable at ambient temperature for a few days during ordinary shipping and time spent in Customs)

Biological Activity

ln Vitro	A biochemical reagent called nonan-1-ol can be utilized in life science research as an organic substance or biological material.
ADME/Pharmacokinetics	Absorption, Distribution and Excretion Skin absorption is low; the dermal flux of 1-nonanol in human skin (epidermis) in vitro is 0.003 mg/sq cm/hr. Metabolism / Metabolites Nonanol, like other primary alcohols, undergoes two general reactions in vivo. The first is oxidation to the carboxylic acid derivative and next the direct conjugation with glucuronic acid. It was reported that nonanol undergoes direct glucuronic conjugation to the extent of 4.1%. This oxidation proceeds with very little inhibition as opposed to that shown by methyl amyl alcohol and 2-ethyl butyl alcohol which form ester glucuronides.
Toxicity/Toxicokinetics	Toxicity Data LC50 (mice) = 5,500 mg/m3/2h Interactions ... Maximum permeation of MT was observed when fatty alcohol carbon chain length was 10. As the level of unsaturation increased from one to two double bonds, there was an increase in the permeation of MT both in porcine and human skin. However, a decrease in the permeation was observed with three double bonds. Regression analysis using the steady state flux data showed a significant positive correlation between porcine and human skin for saturated fatty alcohols (r(2)=0.8868, P=0.0005). Non-Human Toxicity Values LC50 Mouse inhalation 5500 mg/cu m/2 hr LD50 Rat oral 3.56 g/kg LD50 Rabbit dermal 5.66 ml/kg for 24 hr LD50 Mouse ip 0.8 g/kg /Nonyl alcohols/ For more Non-Human Toxicity Values (Complete) data for 1-NONANOL (10 total), please visit the HSDB record page.
Additional Infomation	Nonanol appears as colorless liquid with a rose or fruity odor. Floats on water. Freezing point 23 °F. (USCG, 1999) Nonan-1-ol is a nonanol that is nonane substituted by a hydroxy group at position 1. It has been isolated as a component of volatile oils from plants like Hordeum vulgare. It has a role as a plant metabolite, a volatile oil component, a flavouring agent and an antifungal agent. It is a nonanol and a primary alcohol. Nonan-1-ol has been reported in Francisella tularensis, Humulus lupulus, and other organisms with data available. Mechanism of Action ... Intermediate-chain alcohols (pentanol to octanol) caused channel currents to fluctuate between the fully open and closed state level so that openings occurred in bursts interrupted by brief gaps ... The number of gaps within a burst was dependent on alcohol concentration whereas gap duration was independent of concentration but increased with increasing chain length of the alcohol up to octanol. Nonanol and decanol reduced the mean duration of bursts of openings but did not cause an increase in the number of short closed intervals within a burst. Beyond decanol there was a decline in the ability of the n-alcohols to affect channel function. A saturated solution of undecanol (0.07 mM) reduced the mean open time by 33 + or - 17%, whereas a saturated solution of dodecanol had no significant effect. The current integral per burst was reduced by all the n-alcohols between pentanol and undecanol. The IC50s were as follows: hexanol, 0.53 + or - 0.14 mM; heptanol, 0.097 + or - 0.02 mM; octanol, 0.04 mM and nonanol, 0.16 + or - 0.035 mM ... Blocking rate constants (k+B) for pentanol through to nonanol were calculated to be between 2.8 and 5.7 X 10(6) /M/sec ... Equilibrium dissociation constants (KD), calculated from the blocking and unblocking rate constants (KD = k-B/k+B), decreased with increasing chain length from 8 mM for pentanol to 0.15 mM for octanol. The standard free energy per methylene group for adsorption to the site of action was calculated to be about -3.3 kJ/mol.

Solubility Data

Solubility (In Vitro)

May dissolve in DMSO (in most cases), if not, try other solvents such as H2O, Ethanol, or DMF with a minute amount of products to avoid loss of samples

Solubility (In Vivo)

Note: Listed below are some common formulations that may be used to formulate products with low water solubility (e.g. < 1 mg/mL), you may test these formulations using a minute amount of products to avoid loss of samples. Injection Formulations (e.g. IP/IV/IM/SC) Injection Formulation 1: DMSO : Tween 80： Saline = 10 : 5 : 85 (i.e. 100 μL DMSO stock solution → 50 μL Tween 80 → 850 μL Saline) *Preparation of saline: Dissolve 0.9 g of sodium chloride in 100 mL ddH ₂ O to obtain a clear solution. Injection Formulation 2: DMSO : PEG300 ：Tween 80 : Saline = 10 : 40 : 5 : 45 (i.e. 100 μL DMSO → 400 μLPEG300 → 50 μL Tween 80 → 450 μL Saline) Injection Formulation 3: DMSO : Corn oil = 10 : 90 (i.e. 100 μL DMSO → 900 μL Corn oil) Example: Take the Injection Formulation 3 (DMSO : Corn oil = 10 : 90) as an example, if 1 mL of 2.5 mg/mL working solution is to be prepared, you can take 100 μL 25 mg/mL DMSO stock solution and add to 900 μL corn oil, mix well to obtain a clear or suspension solution (2.5 mg/mL, ready for use in animals). Injection Formulation 4: DMSO : 20% SBE-β-CD in saline = 10 : 90 [i.e. 100 μL DMSO → 900 μL (20% SBE-β-CD in saline)] *Preparation of 20% SBE-β-CD in Saline (4°C，1 week): Dissolve 2 g SBE-β-CD in 10 mL saline to obtain a clear solution. Injection Formulation 5: 2-Hydroxypropyl-β-cyclodextrin : Saline = 50 : 50 (i.e. 500 μL 2-Hydroxypropyl-β-cyclodextrin → 500 μL Saline) Injection Formulation 6: DMSO : PEG300 : castor oil : Saline = 5 : 10 : 20 : 65 (i.e. 50 μL DMSO → 100 μLPEG300 → 200 μL castor oil → 650 μL Saline) Injection Formulation 7: Ethanol : Cremophor : Saline = 10： 10 : 80 (i.e. 100 μL Ethanol → 100 μL Cremophor → 800 μL Saline) Injection Formulation 8: Dissolve in Cremophor/Ethanol (50 : 50), then diluted by Saline Injection Formulation 9: EtOH : Corn oil = 10 : 90 (i.e. 100 μL EtOH → 900 μL Corn oil) Injection Formulation 10: EtOH : PEG300：Tween 80 : Saline = 10 : 40 : 5 : 45 (i.e. 100 μL EtOH → 400 μLPEG300 → 50 μL Tween 80 → 450 μL Saline) Oral Formulations Oral Formulation 1: Suspend in 0.5% CMC Na (carboxymethylcellulose sodium) Oral Formulation 2: Suspend in 0.5% Carboxymethyl cellulose Example: Take the Oral Formulation 1 (Suspend in 0.5% CMC Na) as an example, if 100 mL of 2.5 mg/mL working solution is to be prepared, you can first prepare 0.5% CMC Na solution by measuring 0.5 g CMC Na and dissolve it in 100 mL ddH2O to obtain a clear solution; then add 250 mg of the product to 100 mL 0.5% CMC Na solution, to make the suspension solution (2.5 mg/mL, ready for use in animals). Oral Formulation 3: Dissolved in PEG400 Oral Formulation 4: Suspend in 0.2% Carboxymethyl cellulose Oral Formulation 5: Dissolve in 0.25% Tween 80 and 0.5% Carboxymethyl cellulose Oral Formulation 6: Mixing with food powders Note: Please be aware that the above formulations are for reference only. InvivoChem strongly recommends customers to read literature methods/protocols carefully before determining which formulation you should use for in vivo studies, as different compounds have different solubility properties and have to be formulated differently.  (Please use freshly prepared in vivo formulations for optimal results.)

Preparing Stock Solutions		1 mg	5 mg	10 mg
	1 mM	6.9319 mL	34.6596 mL	69.3193 mL
	5 mM	1.3864 mL	6.9319 mL	13.8639 mL
	10 mM	0.6932 mL	3.4660 mL	6.9319 mL

*Note: Please select an appropriate solvent for the preparation of stock solution based on your experiment needs. For most products, DMSO can be used for preparing stock solutions (e.g. 5 mM, 10 mM, or 20 mM concentration); some products with high aqueous solubility may be dissolved in water directly. Solubility information is available at the above Solubility Data section. Once the stock solution is prepared, aliquot it to routine usage volumes and store at -20°C or -80°C. Avoid repeated freeze and thaw cycles.